Sales: (402) 649-0832
Warranty & Tech Support: (334) 621-9373

Battery FAQs

If talking to a real-life human is more your thing, you can reach out to us via email, phone or live chat with us during business hours.

Frequently Asked Questions

Why choose 16V over 12V?

16 volt will give you a crisper, brighter image on your graphs. It does this all while giving you better returns from your transducer which results in clearer side, down and forward imaging allowing you to unlock the full potential of your graphs and make you a better offshore fisherman.

Maybe you have already noticed your console units with engine running at 14.6 volts look slightly better then your bow units running at 12v this is because of the increase in voltage. 

16 volt is also 20% more efficient than 12 volt, meaning you will get longer run times on the equivalent amp hour rated 12 volt. Example, 16V 80AH will get similar run time to a 12V 100AH. 

Will 16V damage my graphs or void my warranty?

No,  The short explanation for this is, 16V draws 20% less amperage. Amperage is what causes heat in your electronics, which is your electronics number one enemy.. Lets face it you are already running 14.6 on units while engine is running on full charged battery. Plus the units are rated to run above the 16v limits.

Is 16V compatible with my graphs?

Yes, Hummingbird's working voltage is 20 volts, Garmin's is 18 volts and Lowrance is 17.

Working voltage on battery is 16.4 so Lowrance units cannot be turned on while charging unless you purchased the voltage regulator which maintains the stead voltage of 16.4 to equipment.

The run and gun charger can only be run with a voltage regulator installed. This only applies to lowrance units, all other brands can handle the higher voltage when using charger. 

Do I need a specific charger?

Yes. 16V batteries require a special charger and are not compatible with 12V or 36V, or any other chargers. We sell the required 16V LiFePo4 charger on our website. 

What size 16V battery do I need?

  1. Refer to this table under the "16V draw" column in accordance with each of your graphs and transducers.
  2. Add these numbers for each graph and multiply that total by how many hours you spend on the water before recharging. This will give you the maximum total amps required.
  3. Then choose the appropriate size that fits your requirements (either 48AH, 60AH, 80AH, or 100AH).

If your system requires, you are able to wire in parallel to meet your required demand. Best when used with built in waterproof DC charger that will charge the battery when the outboard is running.

What is the importance of the 16v Battery Install Kit?

Our 16V Battery Install Kit gives you the ability to switch from 16V to 12V on the fly. This ensures that you always have a backup plan.

If for some reason the power goes out or you're not able to fully charge, or you plain forget to charge your 16V and you run it dead, this give you the ability to switch over to 12V backup power and keep you on the water.

The kit includes (4) 6AWG battery cables to hook up the 12v and 16v batteries to a 3-position Perko switch to choose 12v or 16v power.

A helpful tip if you are in a remote area with hard-to-get power cord connections and are running the built in DC charger, you can select 12V power for the practice day before and charge the 16V during practice.

What size wiring is needed to carry loads?

We suggest 10AWG to run from batteries to Perko switch and to units.

Our battery install kit comes with (4) 6 AWG battery cables to go to Perko.

If you choose to run main power to a separate fuse box then you only need 14AWG as 16V system carries the load much better than 12V and will not drop voltage, especially since you are running each device on a separate circuit to the fuse box.

Fuse box eliminates the factory fuse holders that are impossible to get to if a problem occurs on the water. But system will accepted other wiring harness from other suppliers. 

Do I need a specific charger for my 12V battery? 

Technically you don't need a specific charger if your current charger has the capability of lithium charging. However, we have different options for charging that allow you to retrofit your current onboard charging system to charge your dedicated electronics battery, for example the run and gun charging system.

Please feel free to reach out to support if you have specific questions.

Troubleshooting

My battery will not take a charge and is showing 0% SOC (state of charge) on the app.

If you completely run your battery down to 0%, there is a chance that your BMS (battery management system) will fall asleep. This issue is easily corrected with the steps below.

Please note: If  you are running a run & gun charger, they are designed to wake up the BMS automatically when the charge cycle starts.

  1. Remove the load from your battery pack by turning the perko switch to the off position.
  2. Connect charger and turn on.
  3. Connect jumper cables from a working 12v or 16v battery to your battery showing 0% for 2 seconds. Positive terminal to positive terminal, negative terminal to negative terminal. 
  4. Remove jumper cables.
  5. Fully charge battery before next use.

Alternate Steps

  1. Remove the load from your battery pack by turning the perko switch to the off position. 
  2. Connect charger and turn on. 
  3. Connect portable battery jumper box to the dead battery and turn on for 2 seconds. 
  4. Remove battery jumper box.
  5. Fully charge battery before next use.

My charger is showing a green and red light.

Check the PowerHouse Lithium app. This is normal is the battery is shown as 100% charged.

If the app does NOT show 100% charged, this is indicative of an incomplete circuit.

  1. Watch the lights as you grab each side of the Anderson connector with one hand. 
  2. Wiggle the Anderson connector back and forth as you continue to watch the lights.
  3. Between your thumb and your index finger, wiggle the cord that is attached directly to the charger module.
  4. Check your circle eyelet connection at the battery to make sure they are secure. 

If one of these lights goes out while wiggling, you have a loose connection.